DJI Agras MG1

This video will show you how to record point A and point B in smart operation mode. The MG-1S is a high performance aircraft capable of offering comprehensive solutions for agricultural care. This video will show you how to record Point A and Point B in smart operation mode. Before we start ensure that the pesticides are in the spray tank. Before recording Point A and Point B press the spray button to discharge nay remaining air in the pump and then stop spraying. Otherwise Point A and Point B cannot be recorded. First toggle the flight mode switch to the p position (p mode) and ensure that the GPS signal is strong. Next toggle the operation mode switch to the M position (manual operation mode). Then fly the MG-1S and makes sure it hovers at Point A on the operating route. Press the button A on the remote controller for 0.6 seconds until Point A is recorded successfully. Or tap the A icon in the app on the built in screen of the remote controller. Next make the Mg-1S hover at Point B on the operation route. Press the B button on the remote controller for 0.6 seconds until Point B is recorded successfully. Or tap the B icon in the app on the built in screen of the remote controller. Then press the back left button C1 or back right button C2 to choose the direction of the operation route. C1 indicates left (L) and C2 indicates right (R). If you do not set a direction the operation route will be set to right by default. Toggle the operation mode switch to the s position (smart operation mode). Finally make the MG-1S hover in place. Press the C1 button and the C2 button at the same time and release them after you hear a “DD” sound. Then the MG-1S will enter continuous smart operation mode and fly according to the preset route while spray pesticides. In smart operation mode you can adjust the spray rate with remote controller based on your needs. If you want to change the operation direction you need to switch from smart operation mode to manual operation mode and press the C1 button or the C2 button.

This video will show you how to update the firmware for your MG-1S aircraft. The MG-1S firmware and remote controller firmware need to be updated separately. The aircraft firmware is updated with DJI Assistant 2. Go to dji.com and enterprise. Visit downloads on the MG-1S product page. Download DJI Assistant 2. Install DJI Assistant 2 and launch it. To power on the aircraft connect the battery to the battery communication port then to the XT90 port. Connect the aircraft to the PC with the Micro USB cable, inserting it into the ISOD data port on the aircraft. Click the MG-1S icon and enter the main screen. Click firmware update. Select the latest firmware version and click upgrade. Click start update. Wait until the update is complete. When the update process shows 100% and an update failed warning is shown it indicates that the update failed. Restart the aircraft and launch DJI Assistant 2 to check whether the current firmware version is the latest. Then the MG-1S aircraft firmware update is complete. If the update fails try to update the firmware again. If it fails several times contact DJI support.

This video will show you how to update the firmware from your MG-1S remote controller. 1. Updating the firmware with SD card. Visit downloads on the MG-1S product page. Download the firmware for the AGRAS MG-1S remote controller to the PC. Unzip the downloaded file and get the bin file. Copy the file to the root directory of a Micro SD card (FAT32 file system). Ensure that there are no other files in the Micro SD card. After the remote controller is turned off insert the Micro SD card to the SD car slot on the remote controller. Power on the remote controller. Go to general settings, Android system settings and update. Click the icon on the upper right corner of the screen and local update. Then click local update and update. Wait about 5 minutes. The update is complete. Note: Check the current version of the remote controller firmware and restart the remote controller. If the update fails format the Micro SD card and copy the bin file to the Micro SD card and update again. 2. Updating the firmware with the MG app. Ensure that the remote controller is connected to the internet. Go to general settings, Android system settings and update. Tap check for update and corresponding firmware will be shown. Tap download and download to start updating. Wait about 5 minutes and the update will be finished. Note: To check the current remote controller’s firmware version restart the remote controller. If the update fails update it again. If it fails several times contact DJI support.